基于改进MobileFaceNet的人脸识别方法北大核心

针对目前大多数人脸识别算法参数多、计算量大,难以部署到移动端和嵌入式设备中的问题,提出了一种基于改进MobileFaceNet的人脸识别方法。通过对MobileFaceNet模型结构的调整,将bottleneck模块优化为sandglass模块,改良深度卷积和逐点卷积的相对位置,适当增大sandglass模块的输出通道数,从而减少特征压缩时的信息丢失,增强人脸空间特征的提取。实验结果表明:改进后的方法在LFW测试数据集上准确率达99.15%,模型大小和计算量分别仅为原算法的61%和45%,验证了所提方法的有效性。     

双酚芴环氧树脂体系热性能和粘接性能研究

环氧树脂是一种性能优异的热固性树脂，在结构胶粘剂和纤维增强复合材料领域应用广泛。但是常见的环氧树脂体系耐热性普遍较差，近年来，航空航天领域对材料的热性能提出了更高的要求，常规的环氧树脂体系已经无法满足耐高温需求。针对该问题，我们设计了一种耐热性较高的双酚芴型环氧树脂体系，并对其热性能和粘接性能进行了研究。在本文中，首先采用流变学方法和DSC研究了其工艺性能，使用DMA和TGA法分析了环氧树脂体系的耐热性能，并通过单搭接剪切试验测试了该环氧体系的粘接性能。结果表明，双酚芴型环氧树脂体系可在180℃固化，固化后的玻璃化转变温度达到190℃，失重5%时的温度为392℃，150℃时的剪切强度为5.8 MPa，展现了优异的耐热性能和粘接性能。     

光栅对石墨烯太赫兹光学性质的影响

在不考虑等离激元诱导效应的情况下，利用玻尔兹曼平衡方程方法从理论上研究了金属光栅结构对石墨烯光电导率的直接影响。研究发现由于光栅对入射光的动量补偿作用，光栅对石墨烯的带内光电导率产生了显著的影响，使得在石墨烯的太赫兹吸收窗口区域出现光电导率峰，并且该光电导率峰可由光栅周期、电子浓度以及温度来调控。该研究有助于深入理解光栅结构对光电材料的影响，并表明光栅-石墨烯体系可以应用于可调谐的太赫兹光电器件，如太赫兹探测器。     

Direct ink writing of vancomycin-loaded polycaprolactone/ polyethylene oxide/ hydroxyapatite 3D scaffolds

Novel inks were formulated by dissolving polycaprolactone (PCL), a hydrophobic polymer, in organic solvent systems; polyethylene oxide (PEO) was incorporated to extend the range of hydrophilicity of the system. Hydroxyapatite (HAp) with a weight ratio of 55–85% was added to the polymer-based solution to mimic the material composition of natural bone tissue. The direct ink writing (DIW) technique was applied to extrude the formulated inks to fabricate the predesigned tissue scaffold structures; the influence of HAp concentration was investigated. The results indicate that in comparison to other inks containing HAp (55%, 75%, and 85%w/w), the ink containing 65% w/w HAp had faster ink recovery behavior; the fabricated scaffold had a rougher surface as well as better mechanical properties and wettability. It is noted that the 65% w/w HAp concentration is similar to the inorganic composition of natural bone tissue. The elastic modulus values of PCL/PEO/HAp scaffolds were in the range of 4–12 MPa; the values were dependent on the HAp concentration. Furthermore, vancomycin as a model drug was successfully encapsulated in the PCL/PEO/HAp composite scaffold for drug release applications. This paper presents novel drug-loaded PCL/PEO/HAp inks for 3D scaffold fabrication using the DIW printing technique for potential bone scaffold applications.     

水力空化改质对重质原油沥青质及性质的影响

利用水力空化过程产生局部的高温、高压、高射流以及强大的剪切力等极端化学物理条件改质处理沙特重质原油，试验结果表明：沙特重质原油经过水力空化改质后粘度由13.61降低至7.22mm2/s，残碳由7.16%降低至6.48%，实沸点蒸馏后减压渣油降低1个百分点。进一步采用APPI FT-IR MS、XRD、FT-IR、SEM和粒度分布等技术研究了水力空化改质对沙重原油分子组成，沥青质团聚体微晶结构、沥青质胶束粒径分布、沥青质官能团、沥青质形貌等方面的影响，从分子角度阐述空化改质重油的机理。研究结果表明：水力空化改质后沙重原油分子量分布、芳烃类化合物缔合作用变小；沥青质对低DBE化合物吸附性能降低；沥青质团聚体微晶结构更加松散；沥青质胶束粒度分布降低；沥青质分子相互团聚作用力减弱。进一步考察了水力空化改质前后减压渣油延迟焦化性能，改质处理后焦炭产率降低1.85个百分点，液体收率和气体产率分别增加1.52和0.33个百分点，水力空化改质对沥青质性质、结构特点的改善能够有效的提高其加工性能。